1-15 of 15
Keywords: mechanical properties
Close
Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Publisher: ASTM International
Article Type: Technical Papers
Adv. Civ. Eng. Matls.. June 2022, 11(1): 354–371.
Paper No: ACEM20220017
Published Online: July 27, 2022
... to six days), f c values ranged from 35 to 47 MPa. 16 09 2021 18 05 2022 27 07 2022 ultra-high performance concrete silica fume silica fume purity mechanical properties thermal set time water-to-cementitious materials ratio References ACI Committee 239 Ultra-High...
Journal Articles
Publisher: ASTM International
Article Type: Technical Papers
Adv. Civ. Eng. Matls.. May 2021, 10(1): 427–439.
Paper No: ACEM20200187
Published Online: November 12, 2021
... are prepared by using the hand layup method followed by the vacuum bagging process. Mechanical properties like flexural, tensile, hardness, and impact properties are evaluated in this article. The dry sliding wear behavior of three different laminates is carried out with pin on disk by varying time, speed...
Journal Articles
Journal Articles
Publisher: ASTM International
Article Type: Technical Papers
Adv. Civ. Eng. Matls.. October 2020, 9(1): 210–226.
Paper No: ACEM20180058
Published Online: April 23, 2020
...-strength counterpart. This paper thus presents a study into engineering characteristics of higher-strength CRC and its benefits to the environment, as well as investigates the ability of micro crumb rubbers to enhance CRC’s mechanical properties. The results revealed that replacing fine aggregate...
Journal Articles
Publisher: ASTM International
Article Type: Technical Papers
Adv. Civ. Eng. Matls.. November 2019, 8(3): 361–375.
Paper No: ACEM20180136
Published Online: November 1, 2019
... behavior when compared with portland cement-based materials, suggesting an intrinsic improved bond between their components. 30 10 2018 14 02 2019 04 04 2019 geopolymers natural fibers interface coating mechanical properties References Herrera-Franco   P. J...
Journal Articles
Journal Articles
Publisher: ASTM International
Article Type: Technical Papers
Adv. Civ. Eng. Matls.. November 2019, 8(3): 275–286.
Paper No: ACEM20190052
Published Online: November 1, 2019
... 2 emissions per unit strength are significantly reduced for LC 3 compared with PC, and with other blends for the first campaign. 04 03 2019 29 04 2019 03 06 2019 concrete limestone calcined clay cement fresh properties mechanical properties durability properties...
Journal Articles
Publisher: ASTM International
Article Type: Technical Papers
Adv. Civ. Eng. Matls.. October 2019, 8(1): 497–510.
Paper No: ACEM20190037
Published Online: August 15, 2019
... mechanical properties microscopic characterization modification mechanism References Hu   B. , Zhang   X. Y. , Zhao   X. , Feng   H. Y. , Wang   S. T. , and Zhao   S. S. , “ Research Progress on Resource Utilization of Waste Rubber Products ” (in Chinese), Materials...
Journal Articles
Publisher: ASTM International
Article Type: Technical Papers
Adv. Civ. Eng. Matls.. February 2018, 7(1): 651–668.
Paper No: ACEM20180066
Published Online: November 27, 2018
... and strength, and these issues are constantly under investigation. In this study, the mechanical properties and permeability of concrete containing calcium carbonate (CaCO 3 ) nanoparticles and fly ash are investigated. For this purpose, concrete specimens with different proportions of nanoparticles and fly...
Journal Articles
Publisher: ASTM International
Article Type: Review Articles
Adv. Civ. Eng. Matls.. February 2018, 7(1): 599–615.
Paper No: ACEM20180065
Published Online: October 31, 2018
... Keywords concrete, fly ash, nanosilica, mechanical properties, durability Introduction The portland cement production in China and India (the two largest cement-producing countries) stood at 2,400 and 286 million tons, respectively [1,2]. However, it is well known that its production is unsustainable...
Journal Articles
Journal Articles
Publisher: ASTM International
Article Type: Research-Article
Adv. Civ. Eng. Matls.. December 2016, 5(1): 212–234.
Paper No: ACEM20160002
Published Online: September 2, 2016
...N. A. Duong; F. Škvára The primary goal of the paper was to study the effects of key factors on the long-term mechanical properties of fly ash-based geopolymer. The factors considered consisted of curing time, humidity, temperature, admixture, and water coefficient. In the study, the geopolymer...
Journal Articles
Publisher: ASTM International
Article Type: Research-Article
Adv. Civ. Eng. Matls.. December 2014, 3(1): 540–553.
Paper No: ACEM20140019
Published Online: December 31, 2014
... transfer and pullout behavior of fibers. 09 05 2014 18 09 2014 07 10 2014 carbon nanofiber mechanical properties surface treatments References Bencardino , F. , Rizzuti , L. , Spadea , G. , and Swamy , R.N. , “ Experimental Evaluation of Fiber Reinforced...
Journal Articles
Publisher: ASTM International
Article Type: Research-Article
Adv. Civ. Eng. Matls.. June 2013, 2(1): 441–456.
Paper No: ACEM20130063
Published Online: August 23, 2013
...Yu Chen; Mei Peng; Ye Zhang; Yanjun Liu With realizing the significant advantages of autoclaved aerated concrete (AAC) in green building development, an experimental investigation was undertaken to study mechanical properties of plain AAC produced in Beijing, China. AAC specimens of six different...
Journal Articles
Publisher: ASTM International
Article Type: Research-Article
Adv. Civ. Eng. Matls.. December 2012, 1(1): ACEM104569.
Published Online: December 7, 2012
... compressive strength mechanical properties concrete high-strength concrete References Wong , R. C. K. and Chau , K. T. , “ Estimation of Air Void and Aggregate Spatial Distributions in Concrete under Uniaxial Compression Using Computer Tomography Scanning ,” Cem. Concr. Res. , Vol. 35...