A hybrid propulsion system for a passenger car is described and its preliminary design and performance discussed. A gas turbine operating in a controlled on-off mode, a generator, a battery pack, an inverter, and an electric motor constitute the power system, with an electronic vehicle management unit supervising the system for control and regulation. Road simulation tests are presented, based on standard ECC driving mission cycles. The turbogas performance might be improved adopting ceramic blades, with a possible increase of the TIT (turbine inlet temperature), and a consequent increase of its efficiency. The paper reports on the first results of a study in progress, within a joint research program between the University of Roma 1 “La Sapienza” and the Italian Research Centre of ENEA-Casaccia.
Skip Nav Destination
e-mail: roberto.capata@uniroma1.it
Article navigation
July 2003
Technical Papers
A Gas Turbine-Based Hybrid Vehicle—Part II: Technological and Configuration Issues
R. Capata,
e-mail: roberto.capata@uniroma1.it
R. Capata
Department of Mechanics and Aeronautics, University of Roma 1–“La Sapienza,” Via Eudossiana, 18, 00184 Roma, Italy
Search for other works by this author on:
E. Cioffarelli,
E. Cioffarelli
Department of Mechanics and Aeronautics, University of Roma 1–“La Sapienza,” Via Eudossiana, 18, 00184 Roma, Italy
Search for other works by this author on:
E. Sciubba
E. Sciubba
Department of Mechanics and Aeronautics, University of Roma 1–“La Sapienza,” Via Eudossiana, 18, 00184 Roma, Italy
Search for other works by this author on:
R. Capata
Department of Mechanics and Aeronautics, University of Roma 1–“La Sapienza,” Via Eudossiana, 18, 00184 Roma, Italy
e-mail: roberto.capata@uniroma1.it
E. Cioffarelli
Department of Mechanics and Aeronautics, University of Roma 1–“La Sapienza,” Via Eudossiana, 18, 00184 Roma, Italy
E. Sciubba
Department of Mechanics and Aeronautics, University of Roma 1–“La Sapienza,” Via Eudossiana, 18, 00184 Roma, Italy
Contributed by the International Gas Turbine Institute of THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS for publication in the ASME JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER. Manuscript received by IGTI Nov. 2001; final revision received by the ASME Headquarters Dec 2002. Associate Editor: R. Gabrielsson.
J. Eng. Gas Turbines Power. Jul 2003, 125(3): 777-782 (6 pages)
Published Online: August 15, 2003
Article history
Received:
November 1, 2001
Revised:
December 1, 2002
Online:
August 15, 2003
Citation
Capata, R., Cioffarelli , E., and Sciubba , E. (August 15, 2003). "A Gas Turbine-Based Hybrid Vehicle—Part II: Technological and Configuration Issues ." ASME. J. Eng. Gas Turbines Power. July 2003; 125(3): 777–782. https://doi.org/10.1115/1.1584475
Download citation file:
Get Email Alerts
Shape Optimization of an Industrial Aeroengine Combustor to reduce Thermoacoustic Instability
J. Eng. Gas Turbines Power
Dynamic Response of A Pivot-Mounted Squeeze Film Damper: Measurements and Predictions
J. Eng. Gas Turbines Power
Review of The Impact Of Hydrogen-Containing Fuels On Gas Turbine Hot-Section Materials
J. Eng. Gas Turbines Power
Effects of Lattice Orientation Angle On Tpms-Based Transpiration Cooling
J. Eng. Gas Turbines Power
Related Articles
The LETHE™ Gas Turbine Hybrid Prototype Vehicle of the University of Roma 1: Drive Cycle Analysis of Model Vehicle Management Unit
J. Energy Resour. Technol (June,2007)
Performance Benefits of a Portable Hybrid Micro-Gas Turbine Power System for Automotive Applications
J. Eng. Gas Turbines Power (February,2011)
A Vision for a Secure Transportation System Without Hydrogen or Oil
J. Energy Resour. Technol (September,2006)
Enery management in Mobile Hydraulics
Mechanical Engineering (June,2013)
Related Proceedings Papers
Related Chapters
Control and Operational Performance
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Outlook
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Defining Joint Quality Using Weld Attributes
Ultrasonic Welding of Lithium-Ion Batteries