Homogeneous charge compression ignition (HCCI) is a new low-emission engine concept. Combustion under homogeneous, low equivalence ratio conditions results in modest temperature combustion products, containing very low concentrations of NOx and PM as well as providing high thermal efficiency. However, this combustion mode can produce higher HC and CO emissions than those of conventional engines. Control of the start of combustion timing is difficult with pre-mixed charge HCCI. Accordingly, in the present study charge preparation and combustion phasing control is achieved with direct injection. An electronically controlled Caterpillar single-cylinder oil test engine (SCOTE), originally designed for heavy-duty diesel applications, was converted to a direct-injection gasoline engine. The engine features an electronically controlled low-pressure direct injection-gasoline (DI-G) injector with a 60 deg spray angle that is capable of multiple injections. The use of double injection was explored for emission control, and the engine was optimized using fully automated experiments and a microgenetic algorithm optimization code. The variables changed during the optimization include the intake air temperature, start of injection timing, and the split injection parameters (percent mass of fuel in each injection, dwell between the pulses) using three different objective (merit) functions. The engine performance and emissions were determined at 700 rev/min with a constant fuel flow rate at 10 MPa fuel injection pressure. The results show the choice of merit or objective function (optimization goal) determines the engine performance, and that significant emission reductions can be achieved with optimal injection strategies. Merit function formulations are presented that minimized PM, HC, and $NOx$ emissions, respectively.

1.
EPA Document, 2000, “Heavy-Duty Engine and Vehicle Standards and Highway Diesel Fuel Sulfur Control Requirements,” EPA Document #: EPA420-F-00-057, Dec.
2.
Marriott, C. D., 2001, “An Experimental Investigation of Direct Injection for Homogeneous and Fuel-Stratified Charge Compression Ignited Combustion Timing Control,” M.S. thesis, University of Wisconsin, Madison, WI.
3.
Kong, S-C., Marriott, C. D., Reitz, R. D., and Christensen, M., 2001, “Modeling and Experiments of HCCI Engine Combustion Using Detailed Chemical Kinetics with Multidimensional CFD,” SAE Paper 2001-01-1026.
4.
Canakci, M., and Reitz, R. D., 2002, “Experimental Optimization of a DI-HCCI-Gasoline Engine Using Split Injections With Fully-Automated Micro-Genetic Algorithms,” Int. J. of Engine Research, 4(1), pp. 47–60.
5.
Marriott, C. D., Kong, S-C., and Reitz, R. D., 2002, “Investigation of Hydrocarbon Emissions From Direct Injection-Gasoline Premixed Charge Compression Ignited Engine,” SAE Paper 2002-01-0419.
6.
Marriott, C. D., and Reitz, R. D., 2002, “Experimental Investigation of Direct Injection-Gasoline for Premixed Compression Ignited Combustion Phasing Control,” SAE Paper 2002-01-0418.
7.
Montgomery, D. T., and Reitz, R. D., 1996, “Six-Mode Cycle Evaluation of the Effect of EGR and Multiple Injections on Particulate and NOx Emissions from a D.I. Diesel Engine,” SAE Paper 960316.
8.
Senecal P. K., and Reitz, R. D., 2000, “Simultaneous Reductions of Engine Emissions and Fuel Consumption Using Genetic Algorithms and Multi-Dimensional Spray and Combustion Modeling,” SAE Paper 2000-01-1890.
9.
Montgomery, D. T., and Reitz, R. D., 2001, “Effects of Multiple Injections and Flexible Control of Boost and EGR on Emissions and Fuel Consumption of a Heavy-Duty Diesel Engine,” SAE Paper 2001-01-0195.
10.
Thiel, M. P., 2001, “Application of Automated Experiments to the Optimization of a Heavy-Duty Direct Injected Diesel Engine for the Simultaneous Reduction of NOx and Particulate Emissions,” M.S. thesis, University of Wisconsin, Madison, WI.
11.
Goldberg, D. E., 1989, “Genetic Algorithms In Search, Optimization and Machine Learning,” Addison-Wesley, Reading, MA.
12.
Senecal, P. K., 2000, “Development of a Methodology for Internal Combustion Engine Design Using Multi-Dimensional Modeling With Validation Through Experiments,” Ph.D. thesis, University of Wisconsin, Madison, WI.
13.
Carroll
,
D. L.
,
1996
, “
Genetic Algorithms and Optimizing Chemical Oxygen-Iodine Lasers
,”
Developments in Theoretical and Applied Mechanics
,
18
, p.
411
411
.
14.
Thiel, M. P., Klingbeil, A. E., and Reitz, R. D., 2002, “Experimental Optimization of a Heavy-Duty Diesel Engine Using Automated Generic Algorithms,” SAE Paper 2002-01-0960.
15.
BP Amoco Indolene Manufacturer Test Sheet.